DAF 95XF ВНУТРЕННЕЕ ОСВЕЩЕНИЕ КАБИНЫ

16. COMFORT CAB/SPACE CAB INTERIOR LIGHTING

The description of the interior lighting can be
divided into:
- Stepwell lighting, driver’s side
- Stepwell lighting, co-driver’s side
- Interior lighting
- Red interior nightlight
- Interior bed lighting, driver’s side
- Interior bed lighting, co-driver’s side
- Bunk lamp
- Storage compartment lighting
- Map-reading lights
STEPWELL LIGHTING, DRIVER’S SIDE
If the driver’s side door is opened, switch E514
will close and the driver’s side stepwell lamp
(C062) will light up. A voltage is also applied
through wire 2600 to pin 17 of the CTE-2 unit
(D550). A voltage will also be applied internally
to connection point 27 of CTE-2 unit (D550),
causing the lamp of the driver’s side interior
lighting (C149) to light up.
If the driver’s side door is closed, a voltage will
be applied to connection point 27 of the CTE
unit for approx. 9 sec. This will result in a
delayed switching-off of the interior lighting. If a
speed signal is applied to pin 18, the delayed
switch off will not function.
The stepwell lighting is independent of the
contact switch position.
STEPWELL LIGHTING, CO-DRIVER’S SIDE
If the co-driver’s side door is opened, switch
E515 will close and the co-driver’s side stepwell
lamp (C063) will light up. A voltage is also
applied to C148 (interior lighting, co-driver’s
side) through wire 2609, diode D708 and wire
2633.
INTERIOR LIGHTING UNDERSIDE ROOF
CONSOLE
A voltage is applied to switch C151 (interior
lighting with middle switch) through fuse E030
and wire 1104. Depending on the switch
position, C151 (interior lighting underside roof
console) will light up.


RED INTERIOR NIGHTLIGHT
A voltage is also applied to switch C735 (interior
nightlight switch) through fuse E028 and wire
1107. Depending on the switch position, C148
(interior nightlight, driver’s side) will light up.
INTERIOR BED LIGHTING, DRIVER’S SIDE
A voltage is applied to connection point 5 of
switch C733 (interior bed lighting, driver’s side)
through fuse E028 and wire 1107. If a connection
is made in switch C733 (contacts 5 and 7), a
voltage will be applied through wire 2644 and
switch C734 (contacts 7 and 5) and wire 2632 to
both of C149’s bulbs.
INTERIOR BED LIGHTING, CO-DRIVER’S SIDE
A voltage is applied to connection point 5 of
switch C731 (interior bed lighting, co-driver’s side)
through fuse E028 and wire 1107. If a connection
is made in switch C731 (contacts 5 and 7), a
voltage will be applied through wire 2611 and
switch C732 (contacts 7 and 5) and wire 2633 to
bulb C148 (normal interior lighting).
BUNK LAMP
The bunk light C115 can be switched with a
switch through fuse E028.
The bunk lamp is independent of the contact
switch position.
STORAGE COMPARTMENT LIGHTING
A voltage is applied to switches E525 (central
upper storage compartment lighting switch) and
E527 (right-hand storage compartment lighting
switch) through fuse E028 and wire 1107. Switch
E525 is used to switch on/off lamp C064 (upper
storage compartment lighting). Switch E527 is
used to switch on/off lamp C066 (right-hand
storage compartment lighting).
TOOLBOX LIGHTING
A voltage is applied to switches E528 (left-hand
toolbox lighting switch) and E529 (right-hand
toolbox lighting switch) through fuse E028 and
wire 1107. Switches E528 and E529 are used to
switch on/off lamps C067 and C068 respectively.


MAP-READING LIGHTS
A voltage is applied to the switches installed in the
map-reading lights on both the driver’s and the
co-driver’s side (C046 and C047 respectively)
through fuse E208 and wire 1107. By pulling out
the map-reading lights, the switch is activated and
the light is switched on.
VARIANTS
Location
9 This location is used to connect a voltage
converter for the radio memory. (The voltage
converter is optional!)

Оглавление...